Відео

Doesn’t the federal government mandate that obsolescent should be illegal?

Recently bought a sebo felix premium from a dealer. It was a floor model so I got $50 off and a box of bags thrown in. I intend to use the vacuum for my house cleaning business but I’ve never spent so much on a vacuum and am feeling unsure if it was a sound purchase. Started my business in March with a shark just to get going, but I know I want a solid machine, bagged, and something that can be maintenance. The sebo invest feels right but I think I’m more concerned with it being a floor model and the cost point of $750. Any advice? Did I get a good deal and I’m just being silly lol?

I have bought one for our house and one for our church. I will NEVER buy another one

Amazon has pretty much every part you normally replace on a vacuum, Shark vacuums included. Torx bit sets can be had for about $10. My Shark requires a #10 and #20 bit. I need to replace the hose that goes from the base into the handle, Amazon $10. I'm debating if it's worth the time to repair a 5 year old vacuum that has been used hard or replace it? I'll probably repair it and have a solid backup.

I must be lucky. I bought a Bissell Cleanview II Bagless in in like 2006 and it's still going. Been looking at Miele and sebo for the day my vacuum dies.

Hey thanks Josh.

Replacing a few bags and a couple filters every year on a Miele vacuum is going to be much better than buying a new shark vacuum every 1 to 2 years. Throwing away 12 vacuum cleaner bags and 3 hepa filters is a lot less wasteful than an entire vacuum.

I bought a plug-in shark stick vac during the pandemic when batteries weren't available for my Dyson stick. Used it a few times, now got the Dyson battery so the shark sits in the closet. Took a look at it in response to this video, and I'll be damned, the beater bar is not replaceable without removing security head screws and (apparently) taking apart the snap-together housing. Never seen a vacuum where the belt and beater bar are not easily replaceable with simple snap in/out parts or at worse cases a few screws. My shark robot vacuum is not like that, all the filter and brushes and everything are very easy to remove and replace.

Those are called OETIKER clips, and they are largely used for BEVERAGE systems. Possible Correction: Where you point and state "this is one of the pumps that has the diode inside the pump, that may be a klixon sensor it is a thermal fuse that will open if the pump gets too hot.

Just bought new revolutionary pet pro 2 and it runs but doesn't spray at either place,could someone please help???

Great video showing how to change the power switch on my DC14. Saved me a lot of money.

Would love more decent domestic products. I buy American made before chinese of course. Germany, Japan usually has great products also.

I'm here because I can't figure out how to get the bottom hose released to get a stray item out. Time for another vacuum, I guess and it WON'T be another Shark! Thank you for this.

Thank you ❤. I love your video. Very straightforward. ❤

It took me almost 2 hours to replace my power cord today, and I came close to breaking it several times while trying to figure out how to take it apart. Fortunately, I do have the required Philips heads anf Torx drivers. No more Sharks for us.

Thanks again Aiden! Great video. The replacement pump from Vacuums R Us works great. You weren’t kidding about the factory clamps being hard to get to and remove.

Great video I'm going back to eureka vacuums

What do you recommend for a good vacuum?

Thank you for taking the time to teach us how to replace the power switch in a Dyson vacuum. Honestly, if it wasn’t for your video, I would have been forced to take my Dyson to a vacuum shop. You saved me about one hundred dollars and a lot of time. By the way, I have a Dyson DC27 and your instructions helped me to quickly fix the switch. Again, thank you for taking the time to do this video!!! 😊

What is the glue u used and were can i get it?

Working on 1 now, that's how I found your video 😢. Thanks for exposing this company, and what they're doing. I got lucky and picked mine up in a garage sale for 10 bucks, I mean I can fix anything, or so I thought. I feel bad for the others though who are having the economy sucked out of them with this scam.

In your opinion what is the best bagless upright

Hey I have an Elna 3003. Do you know what year it came out? And what's your telephone number ;)

I have a cleaning business. I don’t mind buying a new shark once a year. I bought riccar vacuums for years and I got sick of the noise and weight. I wish the upright riccar vacuum could convert to a canister like the shark lift away does so I wouldn’t always need 2 vacuums. I hate regular canisters for vacuuming hard wood floors. I like having easy tools for edging but my riccar super light doesn’t do that. The heavier riccar needs expensive filters changes constantly or it smells horrible. I am irritated that I can’t get the vacuum head apart to clean it out because it’s just stupid.

Yas ty so much

Thank you for making a GR8 ECO point to save our 🌎. Everything is throw away after 1 year & causing too much E-Waste!! So many dead Satellites are just floating around in space. Cost too much to real’em in & then dispose properly.

Yes it upsets me that the first sweeper I bought had a lifetime warranty but they can't find me in the system .I bought another small one can't take it apart to clean it nor replace belt as you say . doesn't even have lights on it which I didn't realize I'm and older lady so my sight not the best .Well this will be the last one I never buy I'm done with this company .what a trip off .

It was going so well! I snapped the ear off (4:36) when trying to knock off the orange knob (6:49). Well, I’m going vacuum shopping. 🥳 Thanks for the video ❤

How to remove the plastic tank float cover. On a Hoover Carpet Cleaner?

Hi, great video, I have a very similar machine, but it doesn’t take the soap, other than that if works fine. Shall I strip it down to see if there is a clog in the soap line? Cheers,

I wish I had ran across this video before I spent $450. That is not your fault though. Thanks for the info. I'll never buy another Shark. I will never own a second shark.

Couldn't afford Riccar, but bought the kid sister Simplicity Jill and couldn't be happier,

So what is a good alternative? Is Dyson actually as good as they are iniwn to be?

Planned obsolescence to the max

Correct it's not that hard

This is why I think it's nuts the big vacuum reviewers don't mention repairibility. So often shark beats Dyson in reviews on performance but at least Dyson sells parts to fix their machines.

Dyson doesn't maintain parts availability for very long after the warranty period ends.

Exactly what I needed. Thanks!!! P.S. We changed the filter several times, but it STILL has the dust, dingy, etc. smell that’s comes out the filter end. Any ideas?

So glad I found this video! This just happened to my vacuum last night!

I have had 2 shark vacuums and you're right. They've made it impossible to even get the bottom open so I can replace the belt. Although the youtube videos I"ve seen for my model show these large, easy to turn with a coin or flat-head screw driver type things that can be used to open the bottom and replace the belts, my machines have those weird star-ish shaped, multiple sized screws, some of them buried deep in these shaft-type holes on the bottom of the head. I will never ever again buy Shark products..... what a scam they've got going on. I'm actually shocked that Costco sells such garbage.

Done with Ricarr as they are now made in china.

Thanks, I had a DC14 brush that wouldn't spin, thanks to your video I realised that the metal bar must be jammed up. Removed the end caps and bar and cleaned up the bar. Put it back together with some fresh lubrication and it's all working again. Thanks, saved me buying a new vac.

Turns out the issue with ours was that the belt to the motor dry-rotted and broke. Nothing wrong with the old clutch, but had to replace it since its the only way to get the belt.

My hose tore in the same place. Thank you for the video super helpful!

Hospital filtration or HEPA filtration?

Interesting the brush roll shut off is a failure point.....I haven't experienced that failing with any vacuum... then again, I don't use the clutch to turn the brush roll on off...becuase I don't use the vacuum to clean hard floors ...I connect the extension hose with the floor brush to do that... really the only time the brushroll gets turned off on mine is when I put it in the upright position.... I did however see a video where a vacuum repair guy said that if you're going to use the clutch to turn the brush roll off... turn the machine OFF first.... then press the clutch to turn it off or on...then turn the machine back on.... what that does? I have no clue. He explained it but that went over my head.

Wow great demo... the spirit reminds me so much of my Cirrus (which I love)

the neat freak in me would die if a bag explosed in my vacuum... Sometimes I long for that satisfaction of changing a full bag but I'm never able to fill a bag... even after 8 months...I think because I live in a 1300 sq foot home bought new in 2004.. and I'm frequently vacuuming all over the place... and there's never a chance for much dirt to accumulate...Even at the 8 month mark... the bag isn't even 1/2 full... but I change it. I do sucked up some activated charcoal pellets every now and then and it keeps the bag smelling neutral.

That is soooo sneaky of them!

Thank you for your video on showing how to change the switch. You saved my wife and I 80 dollars by not having to take our Dyson to the repair store.